Gorilla Liquid Waterproof Patch & Seal - White

1. Clean the surface of dirt, dust, grease and oil. Make sure the surface is completely dry.

2. Stir the contents for 30 seconds until thoroughly mixed.

3. Apply to the surface by brush, roller, trowel, dipped or poured. Make sure the surface is completely covered.

4. Apply several coats to ensure all cracks and holes have been filled. Allow to cure between coats and before exposure to water. Full curing after 24-48 hours.

NOTE: Test finished project with light water exposure to ensure all cracks have been filled. If the test fails, apply additional layers. For gaps larger than 6.5mm fill them with Gorilla Patch and Seal Paste first. Apply between 10°C and 48°C air temperature.

PAINTABLE: Works with both latex and oil-based paints. When painting with oil-based paint, you must first use a primer before painting.

CLEAN UP: Immediately wipe off unwanted material with a dry cloth or paper towel. Use mineral spirits to clean applicators such as brushes and rollers.

• LOW ODOR
• FLEXIBLE
• PAINTABLE
• TEMPERATURE/ UV resistant
• SELF-LEVELING
• APPLIED BY BRUSH, ROLLER, TROUBLE, DIP OR POURING
• CREATES A PROTECTIVE SURFACE
• USE FOR: Roofs, gutters, skylights, flashings, chimneys*, PVC pipe joints, windows, RVs, DIY projects and more!
• GREAT FOR: Metal, Concrete, Wood, Aluminum, Brick, Tile, Fabric, Rubber**, Glass and more!

Not intended for inside firebox or chimney.

** May not work for all types of plastic and rubber.

Not designed for continuous submersion or use below the waterline. The product will cure as soft, rubbery, glossy and flexible for a waterproof seal. It won't feel hard. Always test the product on a small, inconspicuous area to ensure it is suitable for your project.

• APPEARANCE: Thick liquid
• INDOOR/OUTDOOR: Yes
• UV/SUNLIGHT RESISTANCE: Yes
• PAINTABLE : Yes
• APPLICATION TEMPERATURE: 10°C to 48°C for best results
• CURING TIME: 24-48 hours
• FILLING OF CRACKS and fissures up to 6.5 mm
• SHELF LIFE: 2 years unopened

What surfaces will Gorilla Waterproof Patch & Seal Liquid work on?

Gorilla Waterproof Patch & Seal Liquid is designed to seal out water, air and moisture. Surfaces for use include roofs, gutters, skylights, flashings, chimneys*, PVC pipe joints, windows, RVs and other DIY projects. *Please note that this product is not intended for use inside a firebox or chimney. It may not work for all types of plastic or rubber.

How do I remove Gorilla Waterproof Patch & Seal Liquid from my surface?

This material will be difficult to remove from a surface. In case of wet material, wipe off immediately. Use mineral spirits to clean applicators such as brushes and rollers. A textured surface will be much more difficult to clean than a smooth one. For hardened material, a solvent can soften the material, but it can damage the surface around/underneath. Gently cut or scrape the material to try to remove it.

How do I remove Gorilla Waterproof Patch & Seal Liquid from body/skin?

We strongly recommend wearing gloves while working on any project with Gorilla Waterproof Patch & Seal Liquids. If you get it on your fingers or nails, follow these steps:

1) Too uncured, wipe with alcohol with a cloth or paper towel.

2) For hardened material, wash with soapy water to loosen the coating.

Is Gorilla Waterproof Patch & Seal Liquid food safe?

This product is not recommended for direct or indirect food contact and should not be considered food safe.

How should Gorilla Waterproof Patch & Seal Liquid be stored?

Store in a cool and dry place. After each use, remove excess product from the edge of the can with a dry cloth. Press or tap the lid lightly to create a tight seal.

Do I need to do anything special to the product before use?

Stir contents for 30 seconds until thoroughly mixed before each use. After the first use, slight peeling of the skin may occur. Remove the skin layer and stir for 30 seconds.

Gorilla Liquid Waterproof Patch & Seal SDS (DK)